XT09-MI【PDF 19/71 页】MODULE RF 900MHZ 1W 115K W/MMCX

您好，
买卖IC网欢迎您。
请登录
免费注册

15页 16页 17页 18页 [19页]20页 21页 22页 23页

3. ? RF ? Module ? Configuration

3.1. Programming Examples

Refer to the ‘Command Mode’ section [p17] for information regarding entrance into Command

Mode, sending AT commands and exiting Command Mode. Refer to the ‘X-CTU’ section [p69] of

the ‘Development Guide’ for more information regarding MaxStream’s configuration software.

3.1.1. AT Commands

To Send AT Commands (Using the ‘Terminal’ tab of the X-CTU Software)

Example: Utilize the 'Terminal' tab of the X-CTU Software to change the module's DT (Destina-

tion Address) parameter and save the new address to non-volatile memory. This example

requires the installation of MaxStream’s X-CTU Software and a serial connection to a PC.

Note: ?? Do ? not ? send ? com ‐

mands ? to ? the ? module ?

Select the ‘Terminal’ tab of the X-CTU Software and enter the following command lines:

during ? flash ? program ‐

ming ? (when ? parameters ?

are ? being ? written ? to ? the ?

module ? registry). ??

Wait ? for ? the ?? OK ?? sys ‐

tem ? response ? that ? fol ‐

lows ? the ? ATWR ?

command ? before ? enter ‐

Method 1 (One line per command)

Send AT Command

+++

ATDT <Enter>

ATDT1A0D <Enter>

ATWR <Enter>

ATCN <Enter>

System Response

OK <CR> (Enter into Command Mode)

{current value} <CR> (Read Destination Address)

OK <CR> (Modify Destination Address)

OK <CR> (Write to non-volatile memory)

OK <CR> (Exit Command Mode)

ing ? the ? next ? command ?

or ? use ? flow ? control.

Method 2 (Multiple commands on one line)

Send AT Command System Response

+++

ATDT <Enter>

ATDT1A0D,WR,CN <Enter>

OK <CR> (Enter into Command Mode)

{current value} <CR> (Read Destination Address)

OK <CR> (Execute commands)

Note: When using X-CTU Software to program a module, PC com port settings must match the baud

(interface data rate), parity & stop bits parameter settings of the module. Use the 'Com Port Setup'

section of the “PC Settings” tab to configure PC com port settings to match those of the module.

3.1.2. Binary Commands

To Send Binary Commands:

Example: Use binary commands to change the RF module's destination address to 0x1A0D and

save the new address to non-volatile memory.

1.

2.

3.

4.

RT Command must be set to '1' in AT Command Mode to enable binary programming.

Assert CMD (Pin 10 is driven high). (Enter Binary Command Mode)

Send Bytes [parameter bytes must be 2 bytes long]:

00 (Send DT (Destination Address) Command)

0D (Least significant byte of parameter bytes)

1A (Most significant byte of parameter bytes)

08 (Send WR (Write) Command)

De-assert CMD (pin 10 is driven low). (Exit Binary Command Mode)

Note: CTS (pin 9) is high when a command is being executed. Hardware flow control must be disabled

as CTS will hold off parameter bytes.

? ? 2007 ? MaxStream, ? Inc.

????? 19

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

XT09-PKI-EA-NA MODEM RF 900MHZ 1W ETHER INT

XT09-SI MODULE RF 900MHZ 1W 115K W/RPSMA

XU-A11 X-STICK 2.4GHZ USB TO XBEE

XV-8000CB :3 50.3000KHZ+/-60DPS AUTOMOTIVE GYRO SENSOR +/-60DPS

YB03WKW01-6B-JB INDICATOR PB RECT WHT LED ILLUM

YGM1 C518 THERM PTC MINI-BEAD 3MM 180C

YQD120N0006 THERMISTOR PTC OCP 6 OHM 25C

Z4D-A01 PHOTO SENSOR 7.5MM REFLECT TYPE

相关代理商/技术参数

XT09-MI-MESH 功能描述:射频模块 9XTend, 1W Trnsvr MMCX,115000bps,Mesh RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09MINA 制造商:DIGI 功能描述:New

XT09-MI-NA 功能描述:射频模块 9XTend 1W transceiv encryption 9600 bps RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09-MT 功能描述:射频模块 9XTend 1W transceiv onnector 115000 bps RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09-PKC-U 功能描述:射频模块 9XTend 1W USB w/o accessories RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09-PKC-UA 功能描述:射频模块 900Mhz XTend 1W UBS 256-bit AES Encryp RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09-PKC-UA-NA 功能描述:射频模块 9XTend 1W USB w/accessories no AES RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm

XT09-PKC-U-NA 功能描述:射频模块 9XTend 1W USB w/o accessories Intl RoHS:否制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm